Elite External Video Card Install Kit w/ PCI-E x16 Board, PCI-E x1 to USB Adapter, USB 3.0 Cable and Video Power Cable

MX67227 External Video Card Install Kit w/ PCI-E x16 Board, PCI-E x1 to USB Adapter, USB 3.0 Cable and Video Power Cable
MX67227 External Video Card Install Kit w/ PCI-E x16 Board, PCI-E x1 to USB Adapter, USB 3.0 Cable and Video Power Cable

Customer Reviews

Average Rating: 2.8 / 5 With 5 Customer Reviews

Review Submitted!

Your product review has been submitted! Our moderation team will take a look and if meets our submission guidelines you should see it online shortly.

Review Guidelines

  • Please keep your review to your experiences with the product and how well it performs.
  • Please only review product(s) you have used or owned.
  • Please use appropriate language that is suitable for all ages.
  • Review was not provided in exchange for promotional or commercial reimbursement (i.e. monetary, gift cards, free or discounted products).
If the guidelines are not followed your review may not be accepted.
Review Submission
Captcha
  • 1
Sunday, June 13, 2021
By: Tiny Miner
From: Winnipeg

No issues so far - SATA to MOLEX is Fire Concern

Strengths:

- Worked, tested with cheaper card first just in case but they work. - No issues So Far - RX570's running on them fine

Weaknesses:

- Sata to Molex adapters are a fire hazard - No metal ring around screw holes - Holes close to some electronic solder points - Molex Only Power Connection

Additional Comments:

Worked for me, maybe make some paper washers for your screws, dont bite the board material with them. DO NOT USE sata to Molex ... just use a molex connector, up to 2 risers on one molex line from PSU. Full Points Below: - Worked, tested with cheaper card first just in case but they work. - No issues So Far - RX570's running on them fine -Sata to Molex adapters are a fire hazard as Sata connectors will/can burn/melt when/if the car begins to pull too much power through the riser. In the case of 1050ti's with no external power this is enevitible. -No metal ring around screw holes, this could explain people with bad risers as the screw used could bite into the riser board and depending on how the ground layer is routed they may be causing a short inside the board material. - Holes close to some electronic solder points, i used home made paper washers to create a non conducting barrier between them. - Molex Only Power Connection, PCIE would be prefered for fire proofing but then they would need to add a converter on the riser like others and they spared the expense.
Sunday, January 31, 2021
By: Francisco
From: VICTORIA

Mr

Additional Comments:

It works but it should be made very clear using this product as sold with the included SATA to Molex cable for a mining rig which runs 24/7 365 is UNSAFE, sata is rated for 54 watts and the pci port can draw upto 75 watts under load, this can lead to melting and even FIRE. If you get this throw the SATA/Molex adapter in the trash and use direct 6 pin to Molex from your psu.
Tuesday, January 30, 2018
By: Matthew
From: Winnipeg

Riser card

Strengths:

Does it’s job No complications Effective

Weaknesses:

Expensive High failure rate from factory

Additional Comments:

It’s great for what it does, as long as they work. My best advice when buying these is to keep the receipt in case they fail within warranty.
Saturday, January 27, 2018
By: rise
From: calgary

crashed

Weaknesses:

Burned out after 1 month of use, bad quality
Wednesday, November 22, 2017
By: T
From: Winnipeg

Bad riser

Additional Comments:

Did not work. Crashed the rig. Tried with different cards. Bad riser
  • 1